Forum Replies Created

Viewing 9 posts - 1 through 9 (of 9 total)
  • Author
    Posts
  • February 26, 2016 at 6:10 pm in reply to: Soundcard init #1666
    Devan, KD8MST
    User

    is there a command for enabling auto start on raspberry pi?

    February 26, 2016 at 4:45 pm in reply to: Web config overides manual changes other parameters in svxlink.conf #1665
    Devan, KD8MST
    User

    BJ,

    reference this post Aaron mentions a way to keep settings from being overwritten, i had missed it before!
    https://openrepeater.com/forums/topic/new-6-meter-repeater-controller

    February 26, 2016 at 4:40 pm in reply to: Paging? #1663
    Devan, KD8MST
    User

    Dale,
    With the correct audio files and the correct “modules” i believe it could be done and even activated via DTMF, ill have to look into that as it would be a neat feature for say ARES or RACES toning. Any thoughts Aaron?

    Devan

    February 26, 2016 at 4:37 pm in reply to: Web config overides manual changes other parameters in svxlink.conf #1662
    Devan, KD8MST
    User

    BJ,
    I had the same issue and what I ended up doing was using the webgui to do the initial setup for my repeater and then any changes after that I did via a regular text editor and then just restarted the svxlink service manually… as for the webgui resetting the settings when it resets svxlink im not sure how to stop it and i am afraid that when the pi/bbb reboots it will reset those settings again, so instead of running Aarons command for making the svxlink start automatically i think ill set it up as a cron job to avoid all setting being “reeset” to web gui standards. if you find a way to disable the “resetting” of settings please let me know.
    thanks,
    Devan

    • This reply was modified 8 years, 12 months ago by Devan, KD8MST. Reason: add the email follow up
    February 24, 2016 at 4:03 pm in reply to: Soundcard init #1654
    Devan, KD8MST
    User

    Personal opinion is if it works then that’s the way to go hihi I’ll have to do the same on my raspberry Pi

    February 24, 2016 at 8:06 am in reply to: Raspberry Pi 1 Model B #1651
    Devan, KD8MST
    User

    any chance there is an older version kicking around that i could use on PI1

    February 24, 2016 at 8:05 am in reply to: Soundcard init #1650
    Devan, KD8MST
    User

    I am having the same issue with my Raspberry pi I agree it is acting like SVXLINK is just starting up too fast… if I go and run “sudo service svxlink restart” it comes back no problem but a full reboot the sound card fails to be seen.

    February 14, 2016 at 10:09 am in reply to: New 6 meter repeater controller! #1628
    Devan, KD8MST
    User

    As of 2 days ago after many configuration changes over the past week my 6 Meter Repeater controller has been traded out for a Raspberry Pi 2 running svxlink working perfectly with many many compliments on its capabilities and general usability.

    January 27, 2016 at 9:06 am in reply to: Command line logfile? #1583
    Devan, KD8MST
    User

    ok… next question… with the open repeater web gui in place is it possible for me to use all of svxlink’s features if I enable them and configure via command line?

  • Author
    Posts
Viewing 9 posts - 1 through 9 (of 9 total)